Rock Hard technician performing commercial heating system maintenance on Carrier condenser unit in North Texas winter conditions
Heating Maintenance · North Texas

Commercial Heating Maintenance
in North Texas

Scheduled preventative maintenance for commercial heating systems throughout North Texas — before the first freeze exposes a problem you didn't know you had. RTU heat sections, commercial furnaces, and heat pumps, all major brands.

Licensed & Insured
OEM Parts Only
Fast Response
5-Star Rated
Commercial heating maintenance · North Texas

Fall PM catches problems before the freeze does

Commercial heating systems in North Texas sit dormant through spring, summer, and much of fall. When temperatures finally drop — sometimes overnight, sometimes in the form of a multi-day freeze event — every problem that developed during those idle months announces itself at once. A cracked heat exchanger. A failed ignitor. A gas valve that's sticking. A dirty flame sensor that trips the system on the first call for heat.

A fall pre-season maintenance visit finds these issues when there's no urgency — before the first hard freeze puts every HVAC contractor in the region on emergency calls simultaneously. Rock Hard provides scheduled commercial heating PM for businesses throughout North Texas, covering the full heating system inspection checklist before the season demands it.

Rock Hard technician actively servicing commercial Carrier condenser during North Texas winter — close-up of heating system maintenance

What's included in a commercial heating maintenance visit

Heat exchanger inspection — cracks or failures in the heat exchanger allow combustion gases to enter the airstream; this is a safety check, not just a performance one
Ignitor and burner inspection — ignitors degrade over time and often fail on the first cold call after sitting idle; burners inspected for proper flame pattern
Flame sensor cleaning — a dirty flame sensor is the most common cause of commercial furnace lockout on startup; cleaned and tested every PM visit
Gas valve testing — gas valve operation verified; inlet and outlet pressure measured and recorded
Heat rise measurement — temperature rise across the heat exchanger measured against manufacturer specification to verify heating output
Flue and venting inspection — flue pipe integrity, draft, and venting connections checked for obstructions or deterioration
Electrical connections and controls — heating controls, thermostat operation, and zone sequencing verified
Filter inspection and service — dirty filters reduce airflow, stress the heat exchanger, and can cause high-limit trips
Capacitor and contactor testing — on RTUs with heat pump sections, capacitors and contactors tested for the compressor's heating cycle
Full system performance verification — complete heating cycle run-through confirming the system stages correctly and achieves setpoint
Rock Hard technicians performing commercial heating system inspection on rooftop package unit during fall PM visit
Rock Hard technicians opening commercial HVAC unit panel during heating maintenance inspection

Commercial heating maintenance memberships

Our maintenance memberships include scheduled heating PM visits, priority scheduling for repair calls during freeze events, and discounted repair rates when something does need fixing. For businesses in North Texas, a heating maintenance membership is the most practical way to avoid an emergency heating repair during the region's coldest and busiest service periods.

Schedule your fall PM visit before the first cold front

October and early November is the right window for commercial heating PM in North Texas. By the time the first hard freeze arrives, Rock Hard's fall PM schedule is typically full. Get on the schedule before demand peaks.

The cost of skipped heating maintenance

What happens when commercial heating systems don't get fall PM

A cracked heat exchanger found during fall PM costs a few hundred dollars to address before the season. The same crack discovered during a freeze event — after the system has been running with combustion gas leaking into the airstream — creates a safety issue, a potential insurance claim, and an emergency repair during the busiest service period of the year.

Deferred heating maintenance doesn't eliminate problems. It converts preventable scheduled repairs into urgent emergency calls, usually during the highest-demand period, when dispatch times are longest and the cost is highest.

Heat exchanger cracks found before the season — not during one
Ignitor failures caught at PM — not at 2am during a freeze
Flame sensor issues resolved proactively — not as a no-heat lockout
Gas valve and pressure issues identified before safety becomes a concern
Priority dispatch for membership clients during peak winter demand
Call 469-290-7316 Now
Rock Hard technicians on rooftop inspecting commercial heating unit during maintenance
Two Rock Hard technicians checking commercial RTU during heating PM inspection
Rock Hard technician servicing commercial rooftop package unit during heating maintenance visit
Rock Hard technician reviewing wiring diagrams during commercial heating PM planning
Service areas

Serving North Texas businesses

Based in Aubrey, TX — commercial heating service across Denton and Collin Counties and the greater DFW metro.

Frequently asked questions

Commercial heating — answered

What is included in a commercial heating maintenance visit?
A Rock Hard commercial heating maintenance visit covers heat exchanger inspection, ignitor and burner inspection, flame sensor cleaning, gas valve testing, heat rise measurement, flue and venting inspection, electrical connections and controls verification, filter service, and full system performance run-through. For RTUs with heat pump sections we also test capacitors and contactors.
When should I schedule commercial heating maintenance in North Texas?
Fall is the right time — ideally October through early November, before temperatures drop significantly and before the first freeze events. A fall pre-season visit catches ignitor degradation, heat exchanger issues, gas valve problems, and dirty flame sensors while there's no urgency. Waiting until the first freeze to schedule maintenance means competing for dispatch time with every other business in the same situation.
Do you offer commercial heating maintenance memberships?
Yes. Our maintenance memberships include scheduled heating PM visits, priority scheduling for repair calls during freeze events, and discounted repair rates. Membership clients are prioritized during the winter periods when everyone needs service at once.
How does commercial heating maintenance differ from AC maintenance?
Commercial heating PM focuses on combustion components — heat exchanger integrity, ignitor and burner condition, flame sensor cleanliness, gas valve operation, and flue venting. These are different failure modes than AC PM, which focuses on refrigerant charge, coil cleanliness, and electrical components. Both are included in Rock Hard maintenance memberships that cover your system year-round.
What North Texas areas do you serve for commercial heating maintenance?
We serve businesses throughout North Texas including Aubrey, Frisco, McKinney, Prosper, Plano, Allen, Lewisville, The Colony, Princeton, and surrounding communities in Denton and Collin Counties.
Get started

Schedule commercial heating maintenance

Tell us your system type, facility, and North Texas location. We will get you on the fall PM schedule.

RTU heat sections, commercial furnaces & heat pumps — all brands
Licensed & insured · OEM parts · North Texas coverage
Prefer to call?
469-290-7316
1518 Navo Rd Ste A1, Aubrey TX 76227
Request a Free Estimate
We will respond within one business day