Rock Hard Refrigeration crane lowering new commercial rooftop unit during heating system installation in North Texas
Heating Installation · North Texas

Commercial Heating Installation
in North Texas

New commercial heating installation and system replacement throughout North Texas — properly sized, code-compliant, and built for the demands of commercial facilities. RTU heat sections, commercial furnaces, and heat pumps. Crane-assisted lifts included.

Licensed & Insured
OEM Parts Only
Fast Response
5-Star Rated
Commercial heating installation · North Texas

Commercial heating installation — from sizing through commissioning

Most commercial heating in North Texas is delivered through rooftop package units with gas heat sections — the same RTUs that handle cooling in summer switch to heating mode when temperatures drop. When one of those units reaches end of life or fails beyond economic repair, the replacement involves crane equipment, proper sizing, electrical hookups, gas connections, and full system verification. Rock Hard handles the complete process.

We also install dedicated commercial furnaces for facilities that require a separate heating system, and commercial heat pumps for operations seeking year-round efficiency. Every installation is sized correctly for your facility — not matched to the old unit's tonnage, which may have been wrong to begin with.

Proper sizing prevents years of performance problems

Oversized commercial heating systems short-cycle — they heat a space quickly but never run long enough to warm it evenly or run efficiently. Undersized systems run continuously without reaching setpoint during hard freezes. We perform load calculations based on your actual facility before recommending any equipment.

What's included in a commercial heating installation

Load calculation and system sizing — heating load based on square footage, insulation, occupancy, and North Texas climate data
Equipment selection and procurement — RTU with gas heat section, commercial furnace, or heat pump matched to your facility and budget
Crane coordination for RTU installations — crane scheduling, rigging, lift, and rooftop curb placement managed by Rock Hard
Old system removal and disposal — proper refrigerant recovery and EPA-compliant disposal for combined systems being replaced
Gas line connections and testing — gas supply line connections, pressure testing, and leak verification before startup
Electrical hookup and controls — power connections, thermostat wiring, and zone control setup
Code-compliant installation and documentation — all work to Texas commercial HVAC code, fully insured, documentation for permits
System startup and performance verification — heat output testing, temperature rise measurement across the heat exchanger, and controls walkthrough
Rock Hard team guiding new commercial HVAC unit into rooftop position during heating installation
Rock Hard team securing rigging straps before crane lift during commercial heating installation
Crane setting new commercial RTU in final rooftop position during North Texas heating installation

Heating installation for commercial build-outs and renovations

For commercial build-outs, tenant improvements, and facility expansions, we integrate the heating scope with your broader construction timeline. We coordinate with general contractors and other trades, route ductwork and gas lines that don't conflict with refrigeration systems, and deliver a complete installation ready for certificate of occupancy inspection.

Why installation quality matters

The installation determines the system's performance ceiling for its entire lifespan

A commercial heating system installed with accurate load calculations, correct gas pressure, and proper heat exchanger clearances will run efficiently and reliably for 15–20 years. One that's oversized, undersized, or improperly connected will cost more to run, fail more frequently, and need replacement years before its rated lifespan.

Rock Hard doesn't cut corners on sizing or connections because we're the ones who will be maintaining these systems afterward. We have a direct stake in getting the installation right.

Accurate load calculations — not rule-of-thumb sizing
Gas line pressure tested before startup — every time
Heat exchanger temperature rise measured at commissioning
Controls verified across all zones before handover
Full documentation for permits and manufacturer warranty
Call 469-290-7316 Now
Crane suspending commercial RTU with Rock Hard team guiding installation
Rock Hard team lifting commercial HVAC unit onto roof during heating installation
Rock Hard technicians inspecting newly installed commercial heating system
Jason from Rock Hard Refrigeration with white service truck
Service areas

Serving North Texas businesses

Based in Aubrey, TX — commercial heating service across Denton and Collin Counties and the greater DFW metro.

Frequently asked questions

Commercial heating — answered

What types of commercial heating systems does Rock Hard install?
We install rooftop package units with gas heat sections (the most common commercial heating system in North Texas), dedicated commercial furnaces, commercial heat pumps, and combination heating and cooling systems. We handle crane-assisted RTU installations for large units and manage the complete process from equipment selection through system commissioning.
Do you perform crane-assisted commercial heating installations?
Yes. Large commercial RTUs require crane equipment to safely place on a rooftop curb. Rock Hard coordinates and manages crane scheduling, rigging prep, the lift, placement, all connections, and full system commissioning for commercial rooftop heating installations throughout North Texas.
How long does a commercial heating installation take?
A single RTU replacement with crane can typically be completed in one full day. New multi-unit installations or projects requiring significant gas line or electrical work may take 2–3 days. We provide a clear project timeline during the estimate process.
What's included in your commercial heating installation service?
Our commercial heating installation includes load calculation and system sizing, equipment selection, crane coordination for RTU installs, old system removal and disposal, gas line connections and pressure testing, electrical hookup, thermostat and controls setup, code-compliant documentation, and full system performance verification before handover.
What areas do you serve for commercial heating installation?
We serve businesses throughout North Texas including Aubrey, Frisco, McKinney, Prosper, Plano, Allen, Lewisville, The Colony, Princeton, and surrounding communities in Denton and Collin Counties.
Get started

Request a commercial heating installation estimate

Tell us your facility type, heating requirement, and North Texas location. We will provide a detailed installation estimate.

RTU heat sections, commercial furnaces & heat pumps — all system types
Licensed & insured · OEM parts · North Texas coverage
Prefer to call?
469-290-7316
1518 Navo Rd Ste A1, Aubrey TX 76227
Request a Free Estimate
We will respond within one business day